RS PRO 20 → 70W Light Transformer, 230V ac, 11.5V

RS Stock No.: 714-1391Brand: RS PRO
brand-logo
View all in Lighting Transformers

Technical documents

Specifications

Brand

RS Pro

Primary Voltage Rating

230V ac

Secondary Voltage Rating

11.5V

Power Rating

20 → 70W

Dimensions

53 (Dia.) x 22 mm

Depth

22 mm

Minimum Load Requirement

20W

Maximum Temperature

+45°C

Weight

70 g

Type

Electronic

Dimming

Dimming

Dimming Method

Trailing Edge

Diameter

53mm

Minimum Operating Frequency

50Hz

Termination Type

Lead Wire

Protection Features

Over Voltage Protection, Overheating Protection, Overload Protection, Short Circuit Protection

Maximum Operating Frequency

60Hz

Country of Origin

Italy

Product details

Single O/P Round Dimmable Mini Electronic Transformer

IP20 independent transformer for 12 V halogen lamps
Class II protection against electric shock following direct and indirect contact
The transformer is supplied with cables on the primary and secondary circuits
Excellent operating reliability at very high temperatures (ta = 45 °C; tc = 90 °C)
Small compact size
Easy assembly and installation
Protected against overheating, short-circuits, voltage spikes and overloads

Low Voltage Lighting Transformers

Dimming Methods (where applicable):
Leading Edge:
The control device is either a thyristor or triac which blocks power until they are switched on by the control signal. At that point the current flows almost instantaneously and continues to flow until the end of the half cycle of the mains waveform. When the signal reaches zero, the device turns off and no more current is passed until it is triggered again. Turning the power on and off in this manner averages out creating a constant intensity level and by altering the precise trigger point over a period of time the lamp can be dimmed.

Trailing Edge:
Since this method of dimming uses transistor technology it is not limited to just switching, therefore current can be controlled gradually. Transistors can be programmed to pass current at the start of each half cycle, and gradually switch off later. This will control the full amount of power reaching the lamp without the side effects of a step increase in current.

Stock information temporarily unavailable.

Please check again later.

Stock information temporarily unavailable.

P.O.A.

RS PRO 20 → 70W Light Transformer, 230V ac, 11.5V

P.O.A.

RS PRO 20 → 70W Light Transformer, 230V ac, 11.5V
Stock information temporarily unavailable.

Technical documents

Specifications

Brand

RS Pro

Primary Voltage Rating

230V ac

Secondary Voltage Rating

11.5V

Power Rating

20 → 70W

Dimensions

53 (Dia.) x 22 mm

Depth

22 mm

Minimum Load Requirement

20W

Maximum Temperature

+45°C

Weight

70 g

Type

Electronic

Dimming

Dimming

Dimming Method

Trailing Edge

Diameter

53mm

Minimum Operating Frequency

50Hz

Termination Type

Lead Wire

Protection Features

Over Voltage Protection, Overheating Protection, Overload Protection, Short Circuit Protection

Maximum Operating Frequency

60Hz

Country of Origin

Italy

Product details

Single O/P Round Dimmable Mini Electronic Transformer

IP20 independent transformer for 12 V halogen lamps
Class II protection against electric shock following direct and indirect contact
The transformer is supplied with cables on the primary and secondary circuits
Excellent operating reliability at very high temperatures (ta = 45 °C; tc = 90 °C)
Small compact size
Easy assembly and installation
Protected against overheating, short-circuits, voltage spikes and overloads

Low Voltage Lighting Transformers

Dimming Methods (where applicable):
Leading Edge:
The control device is either a thyristor or triac which blocks power until they are switched on by the control signal. At that point the current flows almost instantaneously and continues to flow until the end of the half cycle of the mains waveform. When the signal reaches zero, the device turns off and no more current is passed until it is triggered again. Turning the power on and off in this manner averages out creating a constant intensity level and by altering the precise trigger point over a period of time the lamp can be dimmed.

Trailing Edge:
Since this method of dimming uses transistor technology it is not limited to just switching, therefore current can be controlled gradually. Transistors can be programmed to pass current at the start of each half cycle, and gradually switch off later. This will control the full amount of power reaching the lamp without the side effects of a step increase in current.